Filter Results By:
Products
Applications
Manufacturers
-
product
AC/DC Current Probe, 100 MHz, 15A
N2893A
The Keysight N2893A is a 100 MHz bandwidth, active current probe for InfiniiVision and Infiniium oscilloscopes. The probe features flat bandwidth (DC-100MHz), low noise(<2.5 mA rms) and low circuit insertion loss. Auto demagnetization (degauss) and calibration removes any residual magnetism and unwanted DC offset in the probe. The probe is powered directly by the InfiniiVision and Infiniium Autoprobe interface, eliminating the need for an additional power supply.
-
product
Rogowski AC Current Probe,30 MHz, 300 A
N7042A
The Keysight N7042A Rogowski coil current probe measures AC currents up to 300 A, with bandwidth ranging from 9.2 Hz to 30 MHz. The probe has a thin, lightweight, flexible, and simple-to-use clip-around Rogowski coil that enables current measurement in the most difficult-to-reach parts and confined spaces of a circuit under test. It can also measure large AC current without an increase in transducer size.
-
product
Rogowski AC Current Probe,30 MHz, 600 A
N7041A
The Keysight N7041A Rogowski coil current probe measures AC currents up to 600 A, with bandwidth ranging from 12 Hz to 30 MHz. The probe has a thin, lightweight, flexible, and simple-to-use clip-around Rogowski coil that enables current measurement in the most difficult-to-reach parts and confined spaces of a circuit under test. It can also measure large AC current without an increase in transducer size.
-
product
16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT2
The DT2 module features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
product
Power Monitor, AC- or DC-Powered
109
NAI’s 109 is an AC- or DC-Powered Power Monitor used to monitor voltage, frequency, and phase characteristics of single- or three- phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.The 109 monitor provides three separate control circuits and output relays indicating the condition of each line characteristic. It is ideally suited for rugged defense and industrial applications.
-
product
Mezzanine System
5047
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
product
Dual-Output 28VDC Plastic Relays with Thermal Protection
Series LPD70
Series LPD70 dual-output 28 Vdc plastic relays offer internal thermal protection. They utilize optical isolation for excellent input-to-output isolation. The LPD70 offers a current-limiting output to protect itself and associated load circuits from transient current overloads. During an overcurrent condition, the LPD70 clamps the current to a safe operating value.MSL 6 Available options include:LPBD70 0.25Adc, 33Vdc Load; 4-7Vdc Control;
-
product
Dual-Output 28VDC Plastic Relay with Internal Thermal Protection
Part No. LPD60a
The LPD60a is a dual-output 28Vdc plastic relay with internal thermal protection. The relay utilizes optical isolation to provide excellent input-to-output isolation. The LPD60a offers a current limiting output to protect itself and associated load circuits from transient current overloads. During an overcurrent condition, the LPD60a clamps the current to a safe operating value.MSL 6Available options include:LPBD60a 0.25Adc, 28Vdc Load; 4-7Vdc Control;
-
product
Solid State Relay for AC Power Switching Applications
Part No. 682
The 682 is a state-of-the-art solid-state relay designed for use in AC power switching applications. Back-to-back SCRs are configured for zero-voltage turn-on and can handle current surges up to 8A. The patented circuit design assures the lowest possible EMI by virtually eliminating commutation spikes while maintaining excellent noise immunity.MSL 1 Available options include:682-1 2A, 250Vrms Load; 3.8-32Vdc Control
-
product
4-Amp Solid-State Single Inline (SIP) Four-Pin Relays
Series BS
Series BS 4-amp solid-state single inline (SIP) four-pin relays are designed for mounting on a printed circuit board. BS relays can withstand very high current overloads. The compact size and triac output make the BS relay an excellent choice for switching medium power resistive loads. All Series BS relays are Zero-Cross switching.Available options include:BS24D4A 4Arms, 15-280Vrms, 600Vpeak Load; 3-10Vdc Control
-
product
20 Amp Current Transformer Burden Test Set
1044A
Due to overwhelming demand, TESCO is pleased to re-introduce the 1044A 20 Amp Current Transformer Burden Test Set. This light weight, hand held unit is a simple and inexpensive means whereby a current transformer installation may be quickly checked for many sources of trouble. The 1044A provides utilities a less expensive and more traditional option for checking larger services for potential meter circuit related issues.
-
product
IR Carbon and Sulphur Analyzer
LD-LCSA-A12
IR Carbon and Sulphur Analyzer LCSA–A12 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 25 to 60 seconds and 10 to 30 °C, the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 32-bit sampling improves sensitivity and accuracy.
-
product
Clamp Meter, Auto, True RMS, 400 A AC, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-7226 CAL
The 72-7226 CAL from Tenma is a digital clamp meter. This stable, safe and reliable digital clamp multimeter is designed with large scale integrated circuits and A/D converter as the core as well as overload protection and novel structure which make them a superb tool for electricians. It measures AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, diodes and continuity and also includes data hold, sleep mode and relative mode features. The resistance measurement range from 400 ohm/4kohm/40Kohm/400Kohm/4Mohm/40Mohm (±(1%+2)), frequency measurement range from 10Hz to 10MHz (±(0.1%+3) accuracy). It is 3 3/4 digit digital clamp meter with precise operation, fashionable structure and highly reliable measuring instrument. The meter uses large scale of integrated circuit with double integrated A/D converter as its core and has full range overload protection. It complies with IEC61010, pollution degree 2, overvoltage category (CAT II 600V, CAT III 300V) and double insulation.
-
product
Clamp Meter, Auto, True RMS, 400 A AC, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-7226 CAL DU
The 72-7226 CAL DU from Tenma is a digital clamp meter. This stable, safe and reliable digital clamp multimeter is designed with large scale integrated circuits and A/D converter as the core as well as overload protection and novel structure which make them a superb tool for electricians. It measures AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, diodes and continuity and also includes data hold, sleep mode and relative mode features. The resistance measurement range from 400 ohm/4kohm/40Kohm/400Kohm/4Mohm/40Mohm (±(1%+2)), frequency measurement range from 10Hz to 10MHz (±(0.1%+3) accuracy). It is 3 3/4 digit digital clamp meter with precise operation, fashionable structure and highly reliable measuring instrument. The meter uses large scale of integrated circuit with double integrated A/D converter as its core and has full range overload protection. It complies with IEC61010, pollution degree 2, overvoltage category (CAT II 600V, CAT III 300V) and double insulation.
-
product
Clamp Meter, Auto, True RMS, 400 A AC, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-7226 CAL D
The 72-7226 CAL D from Tenma is a digital clamp meter. This stable, safe and reliable digital clamp multimeter is designed with large scale integrated circuits and A/D converter as the core as well as overload protection and novel structure which make them a superb tool for electricians. It measures AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, diodes and continuity and also includes data hold, sleep mode and relative mode features. The resistance measurement range from 400 ohm/4kohm/40Kohm/400Kohm/4Mohm/40Mohm (±(1%+2)), frequency measurement range from 10Hz to 10MHz (±(0.1%+3) accuracy). It is 3 3/4 digit digital clamp meter with precise operation, fashionable structure and highly reliable measuring instrument. The meter uses large scale of integrated circuit with double integrated A/D converter as its core and has full range overload protection. It complies with IEC61010, pollution degree 2, overvoltage category (CAT II 600V, CAT III 300V) and double insulation.
-
product
Inbuilt External Controller ATE with Touch Screen Features
QT 200NXT
Qmax Test Technologies Pvt. Ltd.
QT 200 nxT is a ultra modern stylish Inbuilt external controller ATE with touch screen features, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software. The vast library support helps you to functionally test host of different IC families. Other features like user-friendly Windows based software, add-on utilities like oscilloscope, RCV meter circuit tracer, etc. makes it a favorite and makes very effective for repairing PCBs without schematic/ circuit diagrams. All these tests are carried out using simple BUT Interface like multipin test clips, probes or custom test fixture
-
product
Strain Sensors
Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.
-
product
Contact Pressure Gauges
WIKA Alexander Wiegand SE & Co. KG
Wherever the process pressure has to be indicated locally and, at the same time, limit values must be monitored, contact pressure gauges find their application. The switch contacts make or break circuits dependent upon the pointer position of the indicating measuring instrument. If the reading is significantly above or below a set value, they trigger an alarm, hence also the term “alarm contact”. Contact pressure gauges are also suitable for starting, stopping or switching processes.
-
product
Elite™ 13.56 MHz RF Plasma Generators
The elite™ Series of RF plasma generators provides state-of-the art technology in a compact air-cooled package. The elite is designed with high speed closed loop control, a class E RF deck and a switching modulator for superior output performance. The elite design utilizes a single printed circuit board assembly for the full rack product virtually eliminating all internal wires and connectors and thereby providing the highest reliability available.
-
product
IGBT Drive
IGBT gate drive photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a photo diode, signal processing circuit and power output transistor on the output side in a single chip. This coupler is designed specifically to provide high common mode transient immunity (CMR) and a high output current, and has an active miller clamp and high switching speed, making it ideal for driving IGBTs and MOS FETs.
-
product
Line Automation Equipment
5000 Series In-line Handler
The Circuit Check 5000 Series In-line Handler is an integrated inline solution that combines automation, fixturing and measurement hardware in addition to other in-line PCBA probe based test stations, while adding a standardized quick change fixture interface. The 5000 series in-line is a unified solution that is software and hardware agnostic, enabling adaptability to a variety of off-the-shelf lower cost ICT, flash and functional test software and hardware.
-
product
Oscillators
OCXO
The OCXO is an oscillator which is temperature controlled (ovenized crystal controlled oscillator). This type of oscillator has a temperature controlling circuit to maintain the crystal and key components at a constant temperature. OCXO''s are typically used when temperature stabilities on the order of 1 x 10-8 or better are required. While this type of oscillator has a tenfold improvement over a TCXO for temperature stability, the OCXO tends to be higher in price and consumes more power.
-
product
Short
FSXE
The FSXE Fixed Waveguide Shorts and the TSXE Tunable Shorts are available for creation of the shorts circuit conditions in waveguides. The TSXE Tunable Waveguide Shorts are movable shorts, adjustable through at least half a wavelength at the low end of the band. The TSXE Shorts consist of movable noncontacting choke plungers within a straight section of waveguide. The FSXE and TSXE Shorts are provided in five waveguide bands between 33 GHz and 225 GHz.
-
product
Surface Potential Measuring Instrument
In the electronic equipment assembly process, there are many items that are charged on the order of kV, such as resin molded products and films. This digital electrostatic potential measuring instrument is suitable for processes with relatively high electrostatic control voltage.The measurement range switching function makes it possible to measure from low potential measurement of electronic devices to high potential measurement of resin molded products, film / printed circuit board manufacturing, etc.
-
product
TightSight™ Clamp Meter, 1000A AC/DC W/TRMS
61-775
*TightSight™ second display*Tapered jaws with hook tip*True RMS current and voltage*AC/DC voltage*Audible continuity*High frequency rejection**Peak hold*Max/min hold*Data hold*Selectable audible and visual alerts when potentially hazardous voltages are detected at the probe terminals*Selectable auto power off*Backlit display*Low battery indicator*Reads accurately on noisy electrical circuits
-
product
TightSight™ Clamp Meter, 660A AC/DC W/TRMS
61-765
*TightSight™ bottom display*Tapered jaws with hook tip*True RMS current and voltage*AC/DC voltage*Audible continuity*High frequency rejection**Peak hold*Max/min hold*Data hold*Selectable audible and visual alerts when potentially hazardous voltages are detected at the probe terminals*Selectable auto power off*Backlit display*Low battery indicator*Reads accurately on noisy electrical circuits
-
product
TightSight™ Clamp Meter, 660 AAC W/TRMS
61-763
*TightSight™ bottom display*Tapered jaws with hook tip*True RMS current and voltage*AC/DC voltage*Audible continuity*High frequency rejection**Peak hold*Max/min hold*Data hold*Selectable audible and visual alerts when potentially hazardous voltages are detected at the probe terminals*Selectable auto power off*Backlit display*Low battery indicator*Reads accurately on noisy electrical circuits
-
product
Test & Support Gear
Atec has experience with rugged and reliable equipment required for oil-field applications and the reputation for customer responsiveness and quick deliveries. Our energy history includes several years of re-engineering and manufacturing several test and support energy products. We have the ability to design, re-engineer and assemble items such as: junction boxes, cables, harnesses, printed circuit boards, computer systems, data acquisition software, valves, solenoids, & gear boxes.
-
product
Linear High Efficiency Power Amplifier
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's high efficiency linear power amplifiers are available for operating frequencies from 1MHz to1 GHz with output power from 1 to 100 watts. Combined with linear design, these linear power amplifiers provide ultra low distortion, suitable for multi-band, multi-mode communication applications. With built-in monitor circuits, Keylink's power amplifier assure consistent performance in terms of reliability. KeyLink's linear power amplifiers can be categorized as follows:
-
product
Vector Impedance Analyser
TE3000
The TE3000 Vector Impedance Analyser is a portable desktop instrument designed for high accuracy impedance measurement. The probe style construction and small output signal make it ideal for "in circuit" impedance characterisation of small signal devices without the risk of damage to the device under test. The TE3000 comes factory calibrated to the tip of the probe with optional custom calibration. Turn it on, set the frequency, take a measurement, and display the results in any format.